“Experimental Investigation for Behavior of Spliced Continuous RC Girders Strengthened with CFRP Laminates”
الباحثونAl-Tameemi, Haider, A. ، Ali, Ammar, Y.and Kadhum, Mohammed, M.;
المجلةJournal of Babylon University/Engineering Sciences
مختصر البحثIn this paper, the behavior of spliced continuous reinforced concrete girders was experimentally investigated. The main objective was to examine the contribution of the carbon fiber reinforced polymer (CFRP) laminates in strengthening the spliced continuous reinforced concrete girders. Eight models of continuous reinforced concrete girder were constructed and tested. The test variables were strengthening the splice joints by different schemes of CFRP laminates, presence of horizontal stirrups through the interfaces of the joints and using binder material at the interfaces of the joints. The results showed that strengthening the continuous spliced girders with 45° inclined CFRP laminates led to an increase in the ultimate load in a range of (47 to 74%). Besides, strengthening the continuous spliced girder with horizontal CFRP laminates bonded at its lateral faces could increase the ultimate load by 70%. Additionally, the ultimate load of the continuous spliced girder was increased by (30%) due to presence of the horizontal steel stirrups through the interfaces of the joints.
Nonlinear Analysis of Spliced Continuous RC Girders Strengthened with (CFRP) Laminates using ANSYS
الباحثون.Al-Tameemi, Haider, A، Ali, Ammar, Y. and Kadhum, Mohammed, M.;
المجلةJournal of Babylon University/Engineering Sciences
مختصر البحثThis paper presents the details of the finite element analysis of spliced continuous reinforced concrete girders. Five spliced continuous girders and one non-spliced continuous girder were analyzed using the ANSYS program. Each spliced girder consisted of three precast segments spliced at two cast-in-place joints at the inflection points, using splices of hooked dowels. Three spliced girders were strengthened using different schemes of the carbon fiber reinforced polymer (CFRP) laminates. The concrete was modeled using (SOLID65) eight-node brick element and the steel reinforcement was modeled discretely using (LINK8) spar element. The straight parts of the spliced bars were modeled using discrete representation with interface elements using (COMBIN39) elements to represent the bond-slip behavior while the hooked part of each spliced bar was replaced by a single spring element. The CFRP laminates were modeled using (SHELL41) shell element. The interfaces between the precast concrete segments and the joints were modeled using CONTAC52 interface elements in conjunction with vertical spring elements to represent the dowel action of the steel bars that crossing the interfaces.
The ANSYS model succeeded to an acceptable degree in predicting the structural behavior of the analyzed spliced girders with average of differences of about 6% between the predicted and experimental ultimate load.
Three-Dimensional Nonlinear Finite Element Analysis of Reinforced Concrete Horizontally Curved Deep Beams” Journal of Babylon University/Engineering Sciences.
الباحثونAl-Tameemi, Haider, A، Ali, Ammar, Y.and Attiya, Ali, N
المجلةJournal of Babylon University/Engineering Sciences.
مختصر البحثThis research deals with the analysis of reinforced concrete horizontally curved deep beams,
loaded transversely to its plane, using a three-dimensional nonlinear finite element model in the pre
and post cracking levels and up to the ultimate load. The 20-node isoparametric brick element with
sixty degrees of freedom is employed to model the concrete, while the reinforcing bars are modeled
as axial members embedded within the concrete brick element. Perfect bond between the concrete
and the reinforcing bars is assumed. The behavior of concrete in compression is simulated by an
elasto-plastic work hardening model followed by a perfect plastic response, which is terminated at
the onset of crushing. In tension, a fixed smeared crack model has been used with a tensionstiffening
model to represent the retained post-cracking tensile stress. Also, a shear retention model
that modifies the shear modulus after cracking is used.
Numerical study is carried out to investigate the effect of the shear length to effective depth
ratio (a/d) on the ultimate load resisted by curved beams. Numerical study is carried out to
investigate the effect of the central subtended angle, boundary conditions, amount of transverse
reinforcement, and using additional longitudinal bars (horizontal shear reinforcement) on the
behavior of reinforced concrete horizontally curved beams with different shear length to effective
depth ratios (a/d).
Two-way shear behaviors in hybrid reinforced concrete flat slabs with inset square ducts
الباحثونAli Imad Al-Bahrani ، Haider Ali Al-Tameemi
المجلةAIP Conference Proceedings
التاريخ2025-05-08
مختصر البحثThis research examined the two-way shear behavior of hybrid concrete slabs with embedded square ducts, investigating five reinforced concrete flat slabs. Four slab specimens were constructed with square ducts going through the thickness of the slab at various positions, while the fifth was constructed using normal concrete with no duct, to act as a control specimen. The test variables were using self-compacted concrete of higher strength around the ducts at various positions. According to the test results, adding a square duct across the full slab thickness at a horizontal distance from the face of the column equal to or less than the slab thickness resulted in a significant decrease in the capacity of punching shear for the flat slabs. Additionally, flat slabs made with hybrid concrete showed better structural behaviors than flat slabs made with normal concrete. For slabs with ducts near the column face, slab punching shear capacity was increased by 12% when high-strength concrete was used to surround the duct, though this effect decreased as the duct was placed further away from the column.