Effect of Waiting Time on Gap Acceptance Characteristics of Change Direction U-Turn
Opening
الباحثونAhlam K. Razzaq، Khawla H.H. Shubber
المجلةIIETA Mathematical Modelling of Engineering Problems
مختصر البحثThis paper investigated the effect of some traffic factors such as waiting time and traffic
volume increasing on gap acceptance characteristics i.e., driver’s behavior, limits of gap
acceptance, critical gap, and the facility capacity. The current study depends on real
field data collected at selected change direction U-turn within Najaf city highways
network (center city of the Najaf governorate located approximately 160 km south of
Baghdad, the capital of Iraq). The study focused on the passenger cars and minibus
drivers maneuvering at change direction U-turn opening as the primary case study. The
statistical analysis approach depended on evaluating traffic factors selected as
parameters and their degree of influence on U-turn capacity. The results of statistical
analysis established that firstly, waiting time range between 21 - 30 sec, lead driver to
enforce opposing direction traffic flow to accept gap size less than that when waiting
time fall in the range of 11 to 20 sec at a confidence interval of 95% for a passenger car.
While, minibus shows results higher than passenger car by approximately 20%.
Secondly, there is a slightly different mean gap acceptance between an interval of (1-
10) and (11-20) sec) for both types of vehicles at the same confidence interval. On the
other hand, results showed the studied U-turn change direction median critical gap equal
to 3.75 sec. and follow-up time was 1.1 seconds. According to Siegloch’s formula the
maximum capacity of 3273 pcu/hr. Other results show that the highest wait time group
interval (when taken as the mean value) is lower than the critical gap. The main
recommendation obtained due to the hazard of studied change direction U-turn is the
importance of control and management it.
Studying the behavior of the concrete mixture with
wheat straw as part of the cement
الباحثونMohammed Abd Al-Kadhim Hameed، Ahlam K. Razzq Alzerjawi and
Zaid Abdulzahra Mahdi
المجلةIICESAT Conference, College of Material Engineering, University of Babylon, Iraq
Journal of Physics
مختصر البحثThis paper is an experimental study that was made on the effects of using Wheat
Straw Ash (WSA) as a partial replacement of cement in the concrete mixture. The control
specimens with ordinary portland cement (OPC) were made and in other specimens, cement
was replaced with 10%, 15%, and 20% of WSA by weight of the cement. Wheat straw locally
available was burned to ash in a controlled manner in the oven, which was used in this study.
The destructive tests included the compressive strength, modulus of rupture, and splitting
tensile strength were carried out on the concrete mixture using WSA at a different percentage
of cement replacement and were and compared with control specimens. The tests result gained
show that the compressive strength decreases when surrogating cement with WSA. While the
modulus of rupture increase with 10 % WSA also, the splitting tensile strength increase with
15 % WSA.
Effect of Silica fume on Cold Mix Asphalt Mixture
الباحثونDr. Ahlam khudair Al-Zarjawi، Zaid Abdulzahra Mahdi& Haneen Hamza Abbas
المجلةIOP Conf. Series: Materials Science and Engineering
مختصر البحثThe cold asphalt emulsion mixture CAEMs is a mixture consisting of asphalt emulsion
with aggregate mixed at room temperature. CAEMs is the most preferred layer in recent
times as it is most safe in terms of the lack of environmentally friendly and healthy
volatile fumes. Many studies have demonstrated that silica fume has significant effects in
improving the engineering properties of asphalt binder and mixture.
Several requirements were conducted on compacted modified CAEMs with silica fume
during the practical program of this research, such as Marshall stability test, density, air
voids, indirect tensile strength (exposed to freezing and thawing conditions and not
exposed to it and the effect of moisture in addition to non-destructive examination using
sound waves .Results of this study prove that using silica fume improved the behavioral
properties of cold mix. Higher Marshall Stability (100%) , Higher tensile strength(219%)
than the conventional mixture( without additives) and had a positive effect on the
resistance to freezing and thawing condition.
Effect of Silica on Hot Mix Asphalt Mixture
الباحثونDr. Ahlam khudair Al-Zajrawi، Bahaa Turki Mashkur&Zaid Abd Al- zahra
المجلةIOP Conference Series: Materials Science and Engineering
مختصر البحثThe hot asphalt mixture is the main layer in flexible paving as it is exposed to
traffic loads and environmental factors which require high resistance, high
durability and good stability to avoid structural deformities that leading to
functional and structural failure. In the past few years. Several tests have been
carried out on the prepared and compact specimens such as density testing,
indirect tensile strength (exposed to freezing and thawing conditions and not
exposed), stability and flow as well as non-destructive test using sound waves.
The results of the tests showed that the specimens, containing silica fume as
apart from filler aggregate (Portland cement) , have high Marshall stability-flow
and extra resistance to tensile strength than conventional specimens that
contain just ordinary Portland cement. All results found to be satisfied the Iraqi
specifications adopted for roads and bridges.
Calculation of optimum silica fume content has achieved for all tests in
order to find overall optimal content which was 4.2%.
Key words: Silica fume, Hot asphalt mix, Stability, Tensile strength, Filler.
Evaluating the effect of air voids and asphalt content on the mechanical
properties of HMA by adopting Indirect Tensile Strength Test
الباحثونDr. Ahlam K Razzaq، Nibras Ali Hussain & Hussein Jalo Mohammed Hasan
المجلةInternational Journal of Engineering & Technology
SPC
مختصر البحثMoisture damage in asphalt mixtures can be defined as the loss in strength and durability due to the presence of water. Iraq road
network is showing severe deterioration such as raveling and stripping because the bond between aggregates and asphalt film is
broken due to water intrusion. To minimize moisture damage, asphalt mixes are investigated to evaluate the effect of air voids,
degree of saturation, percent of asphalt content and the conditioning period.
Several laboratory tests has been conducted during this study included Marshall stiffness test included stability and flow, retained
Marshall stability , indirect tensile strength IDT and resilient modulus of asphalt mixes. Furthermore, the work requests
accounting of voids in total mix percent VTM, voids filed with asphalt VFA, voids in mineral aggregate VMA and degree of
saturation in addition to tensile strength ratio TSR.
The results showed that both the degree of saturation and the compaction effort would led to accelerate the deterioration in hot
mix asphalt performance and its resistant to moisture damage.
Several formulas would create in this study to predict tensile strength ratio from degree of saturation for any asphalt content.
Traffic Characteristics of Two-WayTwo-Lane
(TWTL) Highway in Iraq: Al-Mishkhab Road As A
Case Study
الباحثونAhlam K. Al-Zerjawi1، Hamid A. Al-Jameel and Sajad A. Zagroot3
المجلةICCEET 2020
IOP Conf. Series: Materials Science and Engineering
مختصر البحثTwo-Way Two-Lane (TWTL) highways have been developed rapidly throughout the
world, and they represent a large percentage of the road network spread about the world. In Iraq,
this type of road still has also been adopted widely. Therefore, this study tries to investigate the
two-way, two-lane highway characteristics because very few studies have been devoted to
studying this topic in Iraq. Three sections of this type of highway have been selected along Al-
Mishkhab city as a case study. The data collected include flow, headway, number passing and
speed. A speed gun was used to measured speed in the selected sections. The passing frequency
was high and amounted to about 240passings/hr. Further, the speed distribution was normal. The
results of this study indicate that the number of passing vehicles is up to 240 passes/hr/km at
1200 veh/hr. In addition, as flow increases more than 1200 veh/hr, the number of passing
vehicles decreases because of absence the adequate gap for such passing.