مواقع التدريسيينجامعة الكوفة
0Publications
0Lectures
0Interests

About

Graduated from the Faculty of Engineering in the Department of Civil Engineering for the academic year 2004-2005, the complete master's study in 2012, the teaching of fluid mechanics for three years and teaching facilities Alhaadroleikh in addition to teaching in the scientific in >>>PhD in Civil Engineering, Water Resources Specialization, 2023

Research Interests

6

Publications

8
2018

DETERMINING THE ADEQUATE CREST HEIGHT OF SUPPRESSED RECTANGULAR BROAD CRESTED WEIRS UNDER SUBCRITICAL FLOW CONDITIONS

AuthorsHayder Mohammed Jasim
JournalInternational Journal of Civil Engineering and Technology (IJCIET)
Abstract

In this research, an experimental work was conducted on models of broad crested weirs with different height of crest and different flow conditions, in sub – critical zone, to derive an equation to calculate the adequate height of a broad crested weir as a function of flow parameters such as initial depth, sequent depth, critical depth and Froude number due to the hydraulic jump will be generated downstream the weir . Five laboratory models were used in the experiments with crest heights of 30 cm, 35 cm, 40 cm, 45 cm, 50 cm and 55 cm. Each model will examined under different flow values (37 l/s , 31 l/s, 26 l/s, 11 l/s and 6 l/s.). All experiments were conducted in a laboratory flume with dimensions of (1 m * 1.15 m) in cross section and 18 m length. The flow conditions and geometric parameters of laboratory models were rearranged as a non-dimensional parameters using Л – theorem. The values of each Л will be scheduled and analyzed by the software of SPSS -21 to derive an empirical formula to calculate the non-dimensional height of crest. The value of the coefficient of determination (R2) resulted from the non-linear regression of data to derive the nondimensional formula was very high.

2018

PROPERTIES IMPROVEMENT OF LEAN CONCRETE MIXES USING SILICA-FUME AND POLYMERS

AuthorsHayder Mohammed Jasim AL-Modern
JournalInternational Journal of Civil Engineering and Technology (IJCIET)
Abstract

Lean concrete mixes is a concrete mix with low cement content and high percentages of aggregates, it used in several works such as the blinding concrete under foundations and as leveling course below footings or in mass concrete such as dams. The need to make this layer of concrete in more strength and more durable is important, using polymers such as styrene butadiene rubber ( SBR ) in concrete improve the mechanical strength of concrete and durability and make concrete permeability very low, and also using silica-fume powder leads also to improve the strength of concrete. This investigation studies the effect of using styrene butadiene rubber polymer in different percentages and also silica fume to lean mixes to improve the mechanical properties. Mixes with 10% polymers gives the highest values of mechanical properties with 10 % silica fume , it gives average compressive strength of 24.3 MPa while in reference mix give 13.2 MPa , the flexural strength also increased from 1.24 MPa for lean mixes to 4.8 MPa to silica-polymer mixes .the main reason for using polymers and silica fume is because of these two materials reduce the heat of hydration during mixing and casting concrete, so that is very important in mass concrete.

2013

Investigation of performance of sediment transport formulas based on measured data in Euphrates river, up stream of Al-Abassiya barrage

Authorsأ.د. صالح عيسى خصاف, أ.م.د. كريم راضي , م.مز حيدر محمد جاسم
Journalمجلة كلية الهندسة
Abstract

Reliable predication of sediment discharge is very important element in the evaluation of sedimentation in reservoir , local scour or deposition around hydraulic structure , rriver bed degradation , etc .

2022

Pilot Plant Study on Biological Treatment of Domestic SewageUsing Biopipe System

AuthorsHayder Mohammed Jasem, Kifah Mohammed Khudair
JournalJournal of Ecological Engineering
Date2022-09-01
Abstract

The Biopipe system is the first biological wastewater treatment system designed to remove carbonaceous and nitrogenous substances entirely within a pipe. The transformation mechanisms in the Biopipe system can be mod elled using a physical model, and several experiments have been carried out to this study. The experimental work was carried out at the Al-Barakia wastewater treatment plant (BWWTP) in Iraq’s Najaf governorate that will be done to obtain continuous source of sanitary sewage flow and thus, maintain the pilot plant operation. Two tanks, two pumps, a Flow Control and Measuring Device, PVC Pipes, and an Aeration System make up the physical model. Seeding using activated sludge from a similar plant, The Biopipe system requires 28 days to get steady results and maximal COD, TN and TSS removal efficiency. The tests were carried out on a Biopipe system with recirculation with different value of influent flow rate and different recirculation ratio. The most important findings of the Biopipe system application indicated that system is better for removing COD than TN. When the recircu lation ratio was equal to 9, the removal efficiency of chemical oxygen demand (COD) and total nitrogen (TN) achieved 66.50% respectively. The dissolved oxygen concentration rises to 5.75 mg/l when the recirculation flow rate is increased to 216 m3/day. In addition, it was found that the removal efficiency of biodegradable organics can be enhanced in case of low influent flow rate and high recirculation flow rate

2023

Effect of Biopipe Total Flowrate on Venturi Aerator Performance

AuthorsHayder M. Jasem , Kifah M. Khudair
JournalBasrah Journal for Engineering Sciences
Date2023-07-02
Abstract

There is a vacuum created when water goes past a pipe constriction. Air may be pulled into the main flow by drilling a hole in the pipe nearwhere the vacuum happens. Venturi aerator is an example of the application in action. A vacuum is formed at the suction holes of the Venturitube when there is a small difference in pressure between the input and output sides. To demonstrate the link between total flow rate andVenturi aerator performance, a Venturi aerator (model 1584) was introduced at a specific point in a Biopipe system. For this purpose, aphysical model on a pilot scale was constructed and installed in an existing sewage treatment plant. Dissolved oxygen concentrations weremeasured at four locations along the Biopipe at different values of wastewater flowrates. The study results showed that raising the total flowrate increased the amount of air injected by the Venturi aerator. When the total flow rate was less than 4 m3/hour, the Venturi aerator stopssucking air and produces negative consequences.

2024

Predictive Modeling the Turbidity Response in Al-Saray Water Distribution Network in Najaf Governorate/Middle of Iraq, Using PODDS Model

AuthorsZahraa H. ABED1, Hayder M. JASEM, Hayder S. MOHAMMED
JournalCivil and Environmental Engineering
Date2024-12-17
Abstract

Reducing water turbidity is one of the main issues the water industryis currently experiencing. The ability to predict the spatial probabilityand intensity of discoloration events in distribution systems can leadto the adoption and improvement of proactive operation andmaintenance strategies to reduce turbidity. The main objective of thisstudy is to forecast Using the Prediction of Discoloration inDistribution Systems (PODDS model), simulate the turbidity responsein the Al-Saray water distribution network caused by higher flow ratesand a change in the daily demand pattern for water consumption. Thework covered AL -Saray water distribution network. with took intoaccount the two feed flowrate (FFR) values of the AL-Saray waternetwork, which were (522 and 5870) m3/day. The turbidity responsewas observed to be low when daily flows were supplied to thenetwork, but it increased as the flow increased. The maximumturbidity response was observed when water was fed into the Al-Saray water network at a flowrate of 5780 m3/day. the material layersare conditioned to daily flow, or shear stress. However, when the flowincreases due to an increased demand for water, the fluid's shearstress exceeds the material layers' shear strength, which leads to thematerial becoming mobilized

2024

Review on the Collar Performance in Reduction Local Scour

AuthorsLayla Ali Mohammed Saleh, Hayder Mohammed Jasem
JournalOURNAL`S UNIVERSITY OF BABYLON FORENGINEERING SCIENCES (JUBES
Date2024-12-30
Abstract

ocal scour around the pier is one of the main reasons for bridge failures in the world.Many studies have been conducted to assess the hydraulic performance of different types ofcountermeasures designed against scouring. Generally, the countermeasures can be classifiedinto two groups: flow-altering and bed-armoring techniques. Collar is the most commonly usedcountermeasure to change the flow around the pier, hence reducing local scour depth. This paperbriefly reviews the most up-to-date studies regarding using the collar method as a protectivetechnique for the pier. The reviewed studies indicated that the amount of scour reduction aroundthe collar-protected pier is based on the size, shape, and position of the collar. The rectangularcollar outperforms better than circular, trapezoidal, and triangular shapes under the sameconditions. Additionally, combination the collar with other types of countermeasures canenhance the scour reduction process

2024

Investigation of biopipe system performance using numerical model

AuthorsHayder Mohammed Jasem, Kifah Mohammed Khudair
JournalAIP Conf. Proc.
Date2024-08-30
Abstract

Biopipe system is the first biological wastewater treatment system in which removal processes ofcarbonaceous and nitrogenous compounds are supposed to take place entirely inside a pipe. In this study a Biopipesystem model, a labeled as BPSM, for investigating Biopipe system performance (in terms of soluble substrate removal)and in treating municipal wastewater has been developed. BPSM is based on solving the one-dimensional advection-dispersion equation for multiphase pipe flow (air-wastewater) under pressure in a pipeline including the representation ofall biological processes affecting the concentrations of carbonaceous and nitrogenous compounds by Activated SludgeModel Number3(ASM3). The model was applied on Biopipe system with the inclusive of recirculation with and withoutthe use of final sedimentation unit. The most important findings of BPSM application revealed that the existence of afinal sedimentation unit after the Biopipe system is crucial for the effective removal of biodegradable organics. Where,the removal efficiency of readily biodegradable substrate varied on the ranges (43.3-99) and (14.8-21.3) % when finalsedimentation unit is used and unused, respectively. In addition, it was found that the removal efficiency ofbiodegradable organics can be enhanced in case of final sedimentation absent if very long Biopipe system is used

Lectures

9
View details