مواقع التدريسيينجامعة الكوفة
Ali Kadhim Ekal Al-Saedi
Lecturer

Ali Kadhim Ekal Al-Saedi

0Publications
0Lectures
0Interests

About

holds a Bachelor's degree in Physics from the Faculty of Science, University of Kufa, 2001.
holds a master's degree in physics from the Faculty of Science, University of Kufa, 2011.
PhD in Materials Physics from Kazan Federal University - Russian Federation 2020
I teach at the College of Science, Department of Physics.
Head of Quality Department in Physics Department 2013-2014.
I worked in a nuclear laboratory
I worked for four years in the registration department in the College of Science.

Research Interests

4

Publications

10
2020

Peculiarities of the Synthesis of Ternary Fe-Al-Sn Intermetallic Compound from Mechanically Alloyed Materials

AuthorsA. K. AlSaedi, A. G. Ivanova, E. V. Voronina & A. K. Arzhnikov
JournalMetallurgical and Materials Transactions A
Abstract

A nanostructured Fe65Al30Sn5 alloy has been synthesized by mechanical alloying of elemental Fe, Al, and Sn powders in a planetary ball mill. The structure and phase composition of the as-milled sample and the samples after subsequent heat treatment at 400 °C, 500 °C, and 800 °C were investigated using X-ray diffraction, electron microscopy, 57Fe and 119mSn Mössbauer spectroscopy. We found that the as-milled sample is a nanocrystalline ternary bcc solid solution of the estimated composition Fe62Al32.6Sn5.4. The samples of Fe65Al30Sn5 after annealing are non-uniform materials that mainly comprise the ternary B2 ordered phase Fe65Al30Snx, xSn ≤ 1 at. pct. In addition to the dominant B2 ordered phase, we also identified chemically non-ordered regions, Sn and FeSn, FeSn2.

2020

Estimation of the functions of some iron-based ternary systems within Miedema model and comparison with experiment

AuthorsAli K. Alsaedi, Anna G. Ivanova, Azher A. Habiebb, B.A. Almayahic
JournalResults in Physics
Abstract

The Miedema model is used to estimate the enthalpy of intermetallic compounds and the solid solution of ternary systems. The results showed that the chemical enthalpy values of the binary systems (Fe-Al, Fe-B, Fe-V, Fe-Ga, Al-V, and Al-Mn) are negative. Whereas, the chemical enthalpy values of the binary systems (Fe-Mn and Al-Ga) are positive. The most negative enthalpy is observed for Fe-Al-Ga, Fe-Al-B, and Fe-Al-Sn systems with a mole fraction of 50% of Fe. For ternary systems, the enthalpy varies with the mole fractions of the components. Studies of the products of mechanosynthesis - binary alloy and Fe-Al-based ternary systems: Fe65Al35, Fe65Al35- xMx (Mx = Ga, B, Sn; 5 and 10 at. %) and Fe65-yAl35My (My = Mn, V; 3, 5 and 10 at. %) were confirmed. It concluded that the applicability of the Miedema model for prognostic purposes for estimating the enthalpies and the possibility of obtaining multicomponent systems.

2019

Structural and Phase Transformations Occurring during Preparation of Ordered Ternary Fe–Al–M Alloys (with M = Ga, B, V, and Mn) by Mechanical Alloying

AuthorsE. V. Voronina, A. K. Al’Saedi, A. G. Ivanova, A. K. Arzhnikov, and E. N. Dulov
JournalPhysics of Metals and Metallography
Abstract

The possibility of synthesis of the ordered ternary Fe65Al35 – xМx and Fe65 – yAl35My alloys with x, y = 0, 3, 5, 10 at % and M = B, Ga, V, Mn is studied and conditions of the synthesis are reported. Nanocrystalline metastable disordered ternary alloys are used as the precursor materials for the ordered alloys, which are prepared by mechanical alloying from elemental components. The heat treatment of mechanically alloyed compositions allowed us to reach the single-phase state with the В2 superstructure for the compositions with Ga and V; the single-phase state with the D03 superstructure was reached for the compositions with B and Mn.

2014

Bricks Rn222 Exhalation Rates in Some Samples from Different Countries

AuthorsB.A. Almayahi, Raad O. Hussein, Hayder H. Hussain, Ali K. Alsaedi, A.H. Alasadi and Azhar S. Ali
JournalInternational Journal of Engineering Trends and Technology (IJETT)
Abstract

Radon concentrations in brick samples collected from different countries were measured using the sealed-can technique based on the CR-39 SSNTDs. CR-39 detectors are widely used for radon exhalation rate measurements in bricks under different conditions. The detectors were exposed to standard radon concentration from a standard 226Ra source. The average 222Rn and 226Ra concentrations are found to be 280 Bq m 3 and 1.72 Bq kg 1, respectively. The highest radon exhalation rate was found in Samawah bricks, Iraq. The values of effective radium content are less than the permissible value of 370 Bq kg 1.

2014

Ceramic Rn222 exhalation rates from different countries

AuthorsB.A. Almayahi, Asaad K. Alsaedi, Ali K. Alsaedi, A.H. Alasadi, Azhar S. Ali, Raad. O. Hussein, Hayder. H. Hussain
JournalInternational Journal of Scientific & Engineering Research
Abstract

—In the present study, the alpha radioactivity from radon emanated from some ceramic samples collected from different countries was measured using the can technique, containing CR-39. The average 222Rn and 226Ra concentrations are found to be 371.79 Bq m-3 and 1.68 Bq kg-1, respectively. The highest radon exhalation rate was found in Chinese ceramic. The values of effective radium content are less than the permissible value of 370 Bq kg-1.

2014

Powder Milk Rn222 Exhalation Rate Measurements in Different Kinds

AuthorsAli K. Alsaedi
JournalInternational Journal of Engineering Trends and Technology (IJETT)
Abstract

The application of CR-39 SSNTD technique to the determination of radioactive contaminants in different kinds of milk can be very useful. Radon concentrations in animal milk samples collected from different countries were measured using the sealed-can technique based on the CR-39 SSNTDs. The average 222Rn and 226Ra concentrations are found to be 20.20 Bq m-3 and 0.15 Bq kg-1, respectively. The highest radon exhalation rate was found in sample AL-Mudhish, Oman.

2013

CEMENT 222RN AND 226RA CONCENTRATION MEASUREMENTS IN SELECTED SAMPLES FROM DIFFERENT COMPANIES

AuthorsAli K. Alsaedi, B.A. Almayahi, A.H. Alasadi
JournalASIAN JOURNAL OF NATURAL & APPLIED SCIENCES
Abstract

Solid-state nuclear track detectors (CR-39) are widely used for radon exhalation rate measurements in cement under different conditions. The detectors were exposed to standard radon concentration from a standard 226Ra source. A calibration factor of 0.0107 track cm-2 per Bq d m-3 was determined. The 222Rn and 226Ra concentrations varied from 18Bq m-3 to 178 Bq m-3 and 0.09 Bq kg-1 to 1.30 Bq kg-1, respectively. The highest radon exhalation rate was found in Sulaymanyah, Iraq.

2013

Comparison levels of natural radioactivity for some of agriculture and virgin soil in the Najaf governorate

AuthorsAli Kadhim Ekal, Allawi Hamead Farhan and Hayder Hamza Hussein
Journal مجلة كربلاء العلمية
Abstract

Specific activitiesof the natural radionuclides 238U,232Th and 40K have been measured by gamma –ray spectrometry NaI(Tl) in twenty virgin and agriculture soil samples from Najaf governorate. The range of specific activity of 238U, 232Th and 40K in the virgin soil samples varies from 16.08±4.71 to 37.79±4.16 Bqkg-1, 8.83±3.52 to 42.36±2.33Bqkg-1 and 127.91±11.21 to 756.09±11.14 Bqkg-1 with average values of 27.39±4.46 Bqkg-1, 31.16±3.00 Bqkg-1 and 602.77±10.76 Bqkg-1 respectively, whereas for agriculture soil samples varies from 29.90±5.99 to 78.58±5.50 Bqkg-1 , 26.87±2.98 to 59.31±3.41 Bqkg-1 and 543.64±10.98 to 1104.61±12.23 Bqkg-1 with average values of 51.96±5.04 Bqkg-1, 42.48±3.47 Bqkg-1 and 847±11.26 Bqkg-1 respectively. The radium equivalent activity (Raeq), the absorbed dose rate (D) and the activity concentration index (Iγ) resulted from the natural radionuclides in soil, were also calculated. All values of Raeq were lower than the worldwide average. The average values of (D) and (Iγ) in all soil sample were higher than the permissible limit.

ESTIMATION OF THERMODYNAMIC PARAMETERS OF Ni-Si BASE ALLOYS USING THE SEMI-EMPIRICAL MIEDEMA MODEL

AuthorsAli Kadhim Alsaedi1a, Faiz Salih Abbas, Azhar S. Alaboodi, and Ali Abid Abojassim
JournalFaculty of Science, Universiti Malaya
Abstract

In this paper, we present a calculation method for evaluating the possibility of enhancing the thermal stability of nickel silicide by alloying with metals, which consists in determining the formation enthalpy (ΔH) of nickel silicide using the Miedema model. Changes in formation enthalpy (ΔH) were observed for nickel silicides that were alloyed with Mo, Pt, Pd, W, and Zr. The MAAT (Materials Analysis Applying Thermodynamics) software was used to calculate and plot the formation enthalpy of binary and ternary systems. Based on our calculations, we found that in binary systems, the optimum values to expand the formation enthalpy were 51.28 and 49.57 kJ/mol for nickel silicide alloys. For the ternary system, the results showed that adding Zr could increase monosilicide phase stability.

Effecting the Donor Moieties on the Efficiency of D–π–A System Candidate for Optoelectronic Applications: A DFT Study

AuthorsFaeq A. AL–Temimei, Faiz Salih Abbas and Ali K. Alsaedi
JournalEgyptian Journal of Chemistry
Abstract

The five conjugated D–π–A systems are theoretically analyses by applying the Density Functional Theory (DFT) and Time– Dependent Density Functional Theory (TDDFT) /6–311G (d, p)/B3LYP methodology for the ground and the exaction state at the gas phase. The Gaussian 09 software package was utilized to complete the computations with Gauss View 5.0. The various electron side groups were added as donor–moieties in D–π–A formation to discover highly efficient dyes for Dye- Sensitized Solar Cells (DCCs) applications. The structural, electronic, optoelectronic, photovoltaic, absorption, electronic excitation, dipole moment, regeneration, and electron injection characteristics of all designed systems have been reported. The results showed that the designed dyes have efficient properties such as: good delocalization of HOMO, LUMO with energy gab, effective electron injection, performance charge transfer, subsequent regeneration, large LHE, conversion efficiency, direction transition and strong photo sensitizing. Therefore, these results demonstration that the new D–π–A structures can be considered as a new candidate dye-sensitized for applications in organic solar cells.

Lectures

7
View details