مواقع التدريسيينجامعة الكوفة
Dr. Adel .H Omran Alkhayatt
Professor

Dr. Adel .H Omran Alkhayatt

0Publications
0Lectures
0Interests
0News

About

B.Ch. from Salah Aldeen University(1982) , M.Sc(1998) and PhD(2005) from Babylon University and Al-Mustans98ryah University(Republic of Iraq) in solid state physics and Solid state electronics .

Prof.Dr. in Physics Department/Faculty of Sciences . Member of the Scientific Committee in the physics deparetment. Advisor of Solid State Physics and thin-film materials Laboratory . Member of the Scientific Committee of Nanotechnology unit / Faculty of Engineering and a member of the Supreme Committee research to standardize the curriculum at the University of Kufa and a participating teams to the center of scientific progress for the University of Kufa.Editor Maniger of
the journal of kufa physics and ISOR Applied Physics. Reviewer in many international journals in the Elesvier and Science Direct and Springer Publishers ( Materials Letters , EJP Applied Physics,
Optical and Quantum Electronics (OQEL).
There are many manscripts published in international journals with high impact factor such as Materials Letters , Materials Science in Semiconductors Processing , Optik , ISOR applied physics and etc.
Prof. Dr. in 15/62017

Research Interests

3

Publications

40
2019

Structural, Surface Topography and Optical Characterization of Nanocrystalline MgxZn1-xO Thin Films Grown by Modified Chemical Bath Deposition (SILAR) Method

AuthorsMustafa D. Jaafer, Adel H. Omran Al-khayatt, Salah M. Saleh
JournalJournal of Physics: Conference Series - IOPscience
Abstract

A series of MgxZn1-xO thin films were grown on glass substrates using modified chemical bath deposition (m-CBD) called successive ionic layer adsorption and reaction (SILAR) technique. The crystal structure, surface topography and the optical characterization of the prepared films were studied as a function of Mg/Zn (x) content. It is observed that the deposited films have polycrystalline structure in nature and grown in two phases Hexagonal and cubic. The preferential orientation of the films was absorbed along (002) plane. Structural parameter such as crystallite size, number of dislocation density and micro-strain were also investigated. The crystallite size and surface roughness are increased with the increase of Mg2+ ions content. Thus the results showed that the surface topography and the surface quality of the deposited films can be controlled by Mg2+ ions content. The optical transmittance spectra analysis showed that transmittance increase with the increase Mg2+ content to about 85% for x = 0.75, and the energy band gap increases (2.82 - 3.17) eV as the Mg2+ content increases x = (0.25 - 0.75). These results indicate that the MgxZn1-xO thin films can be potentially used in high-performance ultraviolet optoelectronic devices

2019

Structure, surface morphology and optical properties of CuxZn1-xS/Au NPs layer for photodetector application.

AuthorsAdel H. Omran Alkhayatt , Adel H. Omran Alkhayatt, Azher AbdulWahab Habieb Abbas Hadi Abbas Al-Noaman, Ali Abdulhussein Hameed
JournalJournal of Physics: Conference Series - IOPscience
Abstract

CuZnS and CuZnS/Au NPs layer with different Cu/Zn content thin films have been deposited on heated glass substrate by spray pyrolysis technique at 330 °C and annealed at 450 °C for 1 hour. X-ray diffraction (XRD) results reveals that the structures of all prepared thin films are polycrystalline in nature, with preferential growth orientation along (111) plane corresponding to the cubic ZnS (sphalerite). Two low crystallinity of crystallographic phases corresponding to hexagonal CuS and monoclinic Cu2S were appeared with Cu/Zn different content. Strong diffraction peak of Au NPs appeared in CuZnS/Au NPs layer structure corresponding to the cubic Au gold phase oriented along (111) plane. Structure parameters such as crystallite size and number of crystalline, dislocation density and micro strain have been determined. Scanning Electron Microscopy (SEM) and Atomic force microscope (AFM) images of CZS, and CZS/Au NPs thin films shows smooth, uniform morphology and plated regularly with no detectable micro-cracks. The roughness and r.m.s. roughness was increased with increase of Cu/Zn content from 1.95 nm to 4.36 nm respectively, while it decreased with the exists of Au NPs layer from 20.9nm to 3.99 nm. The energy dispersion x-ray spectroscopy spectra demonstrate the stoichiometry of the deposited films. The optical properties results exhibits red shifted in the fundamental absorption edge towards low energies of CZS (Cu/Zn content) and CZS/Au Nps layer thin films. The optical energy gap has been decreased from (2.56 to 2.34 eV, and 2.62 to 2.32 eV) with respect to Cu/Zn content and Au Nps layer, respectively.

2019

Investigation of structure, optical and photoluminescence characteristics of Li doped CuO nanostructure thin films synthesized by SILAR method

AuthorsInass AbdulahZgaira, Adel H.Omran Alkhayatt Asmahan AsaadMuhmood Shaymaa K.Hussain
JournalScienceDirect ® is a registered trademark of Elsevier B.V.
Abstract

Un-doped and lithium (2, 4 and 6) M% doped copper oxide (CuO) thin films were deposited on a glass substrate using successive ionic layer adsorption and reaction (SILAR) method. Structural, surface morphology, optical and photoluminescence characteristics of un-doped and Li- doped CuO thin films were investigated with respect to Li content. The x-ray diffraction (XRD) results showed that the crystal structure of the deposited films was polycrystalline in nature with monoclinic phase. The average crystallite size of un-doped CuO films was 35.31 nm and decreased to 21.17 nm and 17.65 nm as the lithium dopant content increased to (2 and 6) M%, while the crystallite size was increased to 42.37 nm when Li content 4 M%. The EDX spectra confirmed the existence of the elements of the films. The transmittance of CuO films was decrease from 64% to 50% with increasing of Li dopant content. The values of optical band gap was observed to be at (1.77, 1.65, 1.58 and 1.62) eV with respect to (0, 2, 4 and 6) M% of Lithium dopant concentration. The Photoluminescence spectra reveal that the near band gap emission (NBE) peak is in the visible region at around 690 nm (1.797 eV) that corresponds to the red emission. The Li-doped films did not exhibit any new emissions whereas there is a noticeable decrement in the intensities of the peaks with the increase of Li-dopant concentration.

2019

Characterization of CuO/n–Si pn junction synthesized by successive ionic layer adsorption and reaction method

AuthorsAdel H. Omran Alkhayatt, Mustafa D. Jaafer, Hassan Hadi Ali Al AlakAsala H. Ali
JournalOptical and Quantum Electronics
Abstract

Transparent conducting Copper oxide CuO thin films were successfully synthesized on glass and n-type Silicon substrates by successive ionic layer adsorption and reaction method. The crystal structure, surface texture, optical and electrical properties were studied. The results revealed that the deposited CuO thin films at different cycles number (5, 10, 15), have polycrystalline structure nature with monoclinic phase, and the crystallite size increases with the increase of cycles number. The average roughness and the root mean square values increase with increasing cycles number. The optical energy band gap and Urbach energy was decrement from 2.33 eV and 1.2 eV for 5 cycles to 2.1 eV and 0.82 eV for 15 cycles. The electrical properties of Ni/CuO/n–Si pn junction were studied using current–voltage (I–V) measurements. The barrier heights ( B) of Ni/CuO/n–Si thin films were calculated and its values are (0.716, 0.736, 0.723) eV, for 5, 10 and 15 cycles respectively with an applied bias voltage of 3 V.

2019

Effect of Addition of Silver Nanoparticle on Optical Properties of Polymethylacrelate (PMMA) Films

AuthorsAdel H. Omran Alkhayatt, ,Adel H. Omran Alkhayatt, Salaam Azara Hussain Eqbal Abduljalil Mahdi
JournalJournal of Global Pharma Technology
Abstract

The aim of this work to a realization the effect of adding silver nanoparticles on the optical properties of Polymethylmethacrylate (PMMA) films were prepared by using casting technique At a temperature (50ᵒC) with thickness (8±1μm).The optical properties by measuring the spectra absorbability and transmission as a function of wavelength (200-800) nm. The results showed that the transmittance decreased with increasing doping because of increased impurity resulted holds attenuation in the intensity of incident light with a clear increase of absorption and a decrease in optical reflectivity.as well as calculated the optical constants (α,k, and εr) of the prepared films and the results showed an increase when increasing rate of doping .the real part of the Dielectric Constant conduct like the refractive index, while the imaginary part conduct like the extinction coefficient, as for optical conductivity its values increases with increasing the rate of the silver nanoparticles as well as identifying the types of electronic transitions and calculating energy gaps It was found there is diminution in energy gap for direct electron transmission reaching values (5.4 - 4.9) eV.

2019

Photocatalytic degradation of GRL dye from aqueous solutions in the presence of ZnO/Fe2O3 nanocomposites

AuthorsFouad Sh Hashim , Ayad F. Alkaim, Shymaa M. Mahdi, Adel H. Omran Alkhayatt
JournalComposites Communications
Abstract

Water pollution, due to the increase in human activities (industrial and agricultural), has badly affected the life quality in the past few decades. ZnO nanoparticles and ZnO/Fe2O3 (0.5g and 1g FeCl3) nanocomposites were synthesized by solvothermal technique which used as photocatalyst for the treatment of environmental pollution in water. XRD results show that ZnO NPsand ZnO/Fe2O3 (0.5g and 1g FeCl3) nanocomposites were found to be polycrystalline with a hexagonal wurtzite phase, and the (101) plane had the strongest line. FE-SEM images demonstrate that the ZnO NPs were aggregated, while the samples of ZnO/Fe2O3 showed as highly homogenous in shape and size. EDX spectra of ZnO/Fe2O3 nanocomposites confirm that the elements required in the chemical composition of the prepared samples are present. The presence of all zeta potential values in ZnO/Fe2O3 (0.5g FeCl3) nanocomposites within the positive range only demonstrate that the surface of the particles prepared was homogeneous. The photocatalytic activity of ZnO/Fe2O3 (1g FeCl3) nanocomposite reaches to about 81.1% degradation of GRL dye that was recorded within 200 min, which is appropriate to treat the problem of environmental pollution in water.

2019

Effect of (Ag, Pd) doping on structural, and optical properties of ZnO nanoparticales: As a model of photocatalytic activity for water pollution treatment

AuthorsFouad Sh. Hashima, Ayad F. Alkaimb, Sabreen J. Salima, Adel H. Omran Alkhayatt
JournalChemical Physics Letters
Abstract

This study presents a favorable application to use (Ag, Pd) co-doped Zinc oxide nanoparticles as nanocatalysts in photocatalytic degradation of maxilon blue (GRL) dye. Un-doped ZnO nanoparticles were prepared by hydrothermal method and Ag, Pd and (Ag, Pd) co-doped ZnO nanoparticles by photochemical methods for photocatalytic application. XRD results revealed that ZnO has a hexagonal wurtzite phase with (1 0 1) plane preferred orientation. FE-SEM results demonstrated that the samples with a high agglomeration except at pH11 that have a rod-like shape. FT-IR absorption peak at ~520 cm−1, revealed a slight shift which observed after the doping between (520 and 450) cm−1. Diffuse reflectance shows the band gab of doped ZnO nanoparticles is at 2.61 eV. PL results indicate that (Ag, Pd)/ZnO has a lower recombination rate when compared with Ag or Pd doped ZnO nanoparticles. Novel photocatalytic high activity were observed for (Ag, Pd) co-doped ZnO which is about 95.67% at pH9.

2018

An investigation in to the impact of Ti doping on the structural, optical and sensing properties of spray deposited nanocrystalline ZrO2 thin films

AuthorsAdel H. OmranAlkhayatt, Saleem Azara Hussain Eqbal Abduljalil Mahdi
JournalOptik Volume 159, April 2018, Pages 305-314
Abstract

Pure and Ti doped ZrO2 thin films were prepared by chemical spray pyrolysis method on a glass substrate at 450 °C. XRD results reveal that pure and doped films had polycrystalline structure in nature with tetragonal phase and highly oriented along (011) plane. The crystallite size was increased with increasing Ti content from 17.6 nm to 25.3 nm. SEM images of ZrO2 and ZrO2:Ti thin films showed that the surface seems relatively homogeneous, and the EDX spectra confirm the stoichiometry of the prepared films. AFM measurements showed that the average roughness values were increased after doping with Ti. Optical transmittance of the deposited films high value was about (50%) and decreased with increasing of dopant concentration. The optical band gap decreased from 4.30 eV to 3.01 eV with increasing of Ti content. The ZrO2 and ZrO2:Ti (8%) thin films were investigated as NO2 gas sensor, the results showed a maximum response was at 250 °C and had a stable behavior for detecting NO2 gases. The doped ZrO2 film illustrated a higher response than that of the pure film. The sensing mechanism was modeled according to the oxygen–vacancy mode.

2018

Influence of solution pH and NH3 concentration on some properties of CuO thin films deposited by chemical solution method

Authors Asala H. Ali , Ibtisam J. Abd Ali Al-Fatlawi Ali Hassan Ressen Adel H. Omran Alkhayatt
JournalJournal of Engineering and Applied Sciences
Abstract

Copper oxide (CuO) thin films have been deposited on glass substrates using successive ionic layer adsorption and reaction (SILAR) method. Structural, surface morphology and optical properties of the prepared films were investigated as a function of ammonia solution concentration and the pH of the reaction solution. X-ray diffractometer, AFM, UV-Vis spectroscopy were used to investigate the structure, morphology and optical properties of the films. All the films had exhibited amorphous structure for the films with NH3 concentration 30% and PH 10 which would reflect the low crystallinity and polycrystalline monoclinic structure. The surface morphology study of the deposited films, generally, reveals that the films have uniform smooth surface, and the average roughness and RMS decrease with increasing the ammonia concentration and pH solution. The optical energy band gap was decreases from 2.03 eV and 2.57 eV to 1.92 eV and 2.28 eV with increasing the concentration of ammonia and pH values respectively. It was found that the optimum deposition condition of CuO nanostructure films was with the pH of the reaction solution about 10 and ammonia concentration NH3 of 30%.

2018

Optical band gap Modification and Photodetector Properties of Au NPs Doped CuZnS Thin Films

AuthorsAdel H. Omran Alkhayatt , Azhar Abdul Wahab H. Ali Abdulhussein Hameed
JournalJOURNAL OF KUFA – PHYSICS
Abstract

Au nanoparticles doped CuZnS (CZS) thin films were deposited by spray pyrolysis method (SPD) onto glass and silicon substrates at temperature of 330 ºC and annealed at 450ºC. Cu:Zn:S content was 1:1:2 and Au NPs dopant ratio was 4%, 6% and 8%. The structural, surface morphology, optical and photodetector properties were investigated with respect to the dopant concentration. X–Ray diffraction patterns indicate that the films have low crystallinity and polycrystalline structure nature with ZnS sphalerite cubic phase. The intensity of diffraction peaks and the crystallite size increased with the increase of Au Np's dopant ratio. The SEM images show a homogeneous and smooth uniform surface. Also AFM images reveals that the roughness increased from1.95 nm for CZS (1:1:2) to 2.64 nm for CZS:Au (4%), 4.86 nm for CZS:Au (6%) and 3.82 nm for CZS:Au (8%) thin films, these increases could be probably due to the increasing concentration of atomic gold in the CZS thin films, The average grain diameter was evaluated from the plane view images for 68.99 CZS 1:1:2 and CZS:Au NPs was (93.59–102.07 nm). Au Np's dopant ratio, the lower band gap corresponds to CuxS phase and double band gap confirms the alloy nature of material. The decreased in energy band gap after increasing of Au Np's dopant ratio can be attributed to the red shift of the absorption edge and to the improvement in the crystallinity, increase of Au Np's ratio leads to decrease band gap from 2.5 eV to 2.39 eV. Photodetectors CuZnS: Au Np's/Si were synthesized and I–V characteristics have been investigated, the results showed that the photocurrent increased from 0.0 to (8.65×10-7 A, 5.62×10-6 A and 5.03 ×10-6 A) at the bias voltage range of 0– 2V under illumination, and from 0.0 to (3.49 ×10-7 A, 1.9 ×10-6 A and 3.14 ×10-6A) in the dark for CZS:Au NPs (4%, 6% and 8%) ratio, respectively. Under applied voltage of 2V, the response time was (0.8, 0.5 and 1.5 sec) respectively; whereas the recovery time was (0.6, 0.9 and 1.35 sec) and the sensitivity increased from 42.86% to 122.73%.

2018

Antibacterial Activity of Mono and Bimetallic Au:Ag Colloidal Nanoparticles Prepared by Pulse Laser ablation PLA

AuthorsAdel H. Omran Alkhayatt1 , Adel H. Omran Alkhayatt Mahdi Husain Moheel Mohammad Malik Abood
JournalJOURNAL OF KUFA – PHYSICS
Abstract

Au, Ag mono and Bimetallic Au:Ag colloidal nanoparticles were synthesized in two steps using pulsed laser ablation in liquid technique (pure Au, Ag metal plates of immersed in deionized water). The pulse laser (Q-switched, Nd: YAG)1064 nm with energy 700 mJ, frequency 5 Hz and 200 laser pulses at room temperature have been used. Absorbance (SPR band), size, surface morphology and structure of the synthesized Nps have been studied and investigated by UV-Vis spectrophotometer, transmission electron microscopy, and x-ray diffraction. The absorbance spectrum of Au, Ag and Au:Ag nanoparticles shows sharp and single peaks around 513 nm, 398 nm and 523 nm respectively. This gives indicate that the production of pure and spherical Au and Ag NPs with average size in the range 16 - 100 nm. The particles size measurements were confirmed by TEM. The Au:Ag nanoalloy appears to be nearly spherical with an average size ranging from 29 to 72 nm. and the SPR band at (450 nm ). The XRD result showed very low crystallinity structure. The antibacterial activity of Au, Ag and bimetallic Au:Ag NPs were evaluated for NPs obtained by PLAL using applied pulses (100,150,200) in DI water, on the Gram-positive isolate (Staphylococcus aureus) and Gram-negative isolate (Escherichia coli). The results and images of inhibition zones diameter showed that the NPs have synergistic effects on the studied bacteria up to 15 mm and 4 mm at the highest and lowest values and it increase with the increase of laser pulses number.

2018

Influence of Ag Dopant Content on Structural and Optical Energy Gap of Zns Thin Films Deposited By Spray Pyrolysis Technique

Authors Inass Abdulah Zgair, Asmahan Asaad Muhmood and Adel. H. Omran Alkhayatt , Inass Abdulah Zgair, Asmahan Asaad Muhmood and Adel. H. Omran Alkhayatt
JournalTransylvanian Review
Abstract

In this study, pure and Ag doped ZnS thin films were prepared onto glass substrates using spray pyrolysis deposition (SPD) method. 0.1 M and 0.2 M of zinc chloride ZnCl2, thiourea (NH2)2CS and 0.1 M of silver nitrite Ag (NO3) 2 as a source of Zn, S and Ag respectively. The spray deposition parameters was kept at nozzle – substrate distance 30 ± 1 cm, air pressure 1 mbar, spray time 3 minute and substrate temperature was 450 oC. Structural and optical properties have been studied using x-ray diffraction technique in the diffraction angle rang (20-50)o and UV-Vis spectrophotometer in the wavelength range (300-800) nm. The effect of Ag dopant content on the structure parameters such as crystallite size and lattice constants (a, c) and on the optical transmittance, absorbance and forbidden energy gap were investigated. XRD measurements demonstrated that ZnS thin films had polycrystalline structure with hexagonal phase. The average crystallite size was increased from (16.63 nm to 37.80 nm) by increasing Ag concentration from pure to 8% Ag while the dislocation density and the strain decrease with increase of dopant concentration due to enhancement of crystallinity. In the ultraviolet region, the optical transmittance of these films with changing of dopant concentrations of silver was observed to be more than (92%) and the optical absorption edge shifted toward lower wavelengths "blue shift". The value of energy band gap of ZnS films was found to be at (3.02, 2.91, 3 and 3.15) eV with (0, 4, 6 and 8) % of silver dopant concentration, the broadening of the band gap was due to Burstein–Möss effect. From these results it can be conclude that the fabricated ZnS: Ag thin films was suitable for solar cells, optical coating and blue LED applications.

2018

Fabrication of a Solar Cells by Organic – Inorganic Hybrid Perovskites

AuthorsBaron Aref S, Kasim Sattar J., Omran Adel H
JournalIndian Journal of Public Health Research & Development
Abstract

One of the important electronic applications in recent years is organic-inorganic hybrid perovskite materials because of their many useful characterizations particularly the low cost, tunable optical properties and higheffciency. In this work we used varieties of lead halides, PbCl2 and PbBr2 to prepare two types of perovskites, MAPbBr3and MAPbBr2Cl by one step method then study their properties; structural, morphological and optical properties, to fabricate solar cells from these perovskites with preparation of TiO2 nanocrystal as electron transport material ETM by hydrothermal method. The power conversion effciency PCE achieved is 1.2% and fll factor FF=0.26 for MAPbBr3 perovskite while the power conversion effciency PCE for MAPbBr2Cl perovskite reached up to 0.9% and fll factor FF= 0.25.

2018

Seed Layer Thickness Effect on the Structural and Optical Characterization of TiO2 Nanostructure Thin Film

AuthorsAdel H. Omran Alkhayatt, Hussein Hussein Ahmed
JournalIndian Journal of Public Health Research & Development
Abstract

In this research Titanium dioxide (TiO2) nanostructure thin flms have been prepared by chemical bath deposition method on a deferent thickness of seed layer (1, 2 and 3)layers which deposited by sol-gel spin coating technique. Structural and optical characteristics were investigated as a function of the seed layer thickness using x-ray diffraction and UV-Vis spectrophotometer. The results showed that the TiO2 thin flms have a polycrystalline structure in nature with anatase phase and tetragonal crystal structure. The dislocation density, the number of crystallite and the strain of the prepared flms were also investigated. The optical properties results showed that the thin flm transmittance decrease with increasing the thickness of the seed layers, where the transmittance highest value was in the visible region about 53% at wave length 531 nm. The increasing of number of seed layers that lead to increase the thickness of the seed layer and the thin flm which leads to increase the flms absorbance. The energy band gap of allowed direct transition was decreased with the increase of the number of seed layers (thickness) from 3.378 eV to 3.067 eV with increase the thickness from 105.7nm to 156.6 nm for one layer and three layers respectively.

2017

Studying the Optical Properties of Epoxy Panel doped with Al-Anthedin Dye

AuthorsAdnan F. Hassan, Adel H. Omran Alaa M. Mohamed Nibras F.Ali
JournalJOURNAL OF KUFA – PHYSICS, Vol.9, No.1 (2017)
Abstract

In this work the luminescent solar concentrators (LSC) plates doped with Al-Anthedin dye was prepared by at the solid state laboratory at room temperature with different thicknesses and concentrations .The Anthedin dye concentrations were (1×10-4, 2×10-4and 3×10-4) mol/L. The optical characteristics have been studied such as absorption and energy gap also the optical constants such as the absorption coefficient and extinction coefficient were calculated for all panels. Increasing the concentration of the Al-Anthedin dye led to increase the values of absorbance, absorption and extinction coefficient. The results also demonstrate that the value of the energy gap was decreased with increasing the concentrations from (2.2eV) for the lowest concentration to (2.1eV)for the highest one.

2017

Fluorine dopant concentration effect on the structural and optical properties of spray deposited nanocrystalline ZnO thin films

AuthorsAdel H. Omran Alkhayatt , Shymaa K. Hussain
JournalSurfaces and Interfaces
Abstract

Elsevier / Science Direct

2017

Synthesis and study the structural properties of Nano crystalline pure and Co doped ZrO2 thin films by chemical spray pyrolysis method for No2 Gas sensing application

AuthorsEqbal Abduljalil Mahdi, Saleem Azara Hussain Adel H.Omran Alkhayatt
Journalمجلة كربلاء للعلوم
Abstract

In This Study the physical properties of thin films of pure Zirconium Oxide (ZrO2) and doped by Cobalt and Titanium (Co)with percentages (4, 8, and 12)%, which prepared by using the spray chemical thermal on substrates of the glass of temperature of 450ᵒC and 1bar of pressure. For this study and the folling study, we build a chemical spray thermal system configured to prepare thin films. The properties includes structural, and Sensitivity. The structural properties of the films were studied by X-ray diffraction. It had been noticed that pure ZrO2 films and doped with (Co,Ti) were polycrystalline with Tetragonal type preferred direction (011). The doping process leads to improve the crystal structure of the prepared thin films, as well as the calculation of structural parameters and the constants and size grained results showed an increase in the grain size of the crystallites with increase rates of doping, Through texture coefficient calculation found that the preferred level of growth[011]. The morphology of the surface was examined by using scanning electron microscope (SEM) and found that the films with a dense and homogeneous distribution. Intensity has increased the particle and the size of grain crystalized when doped. The atomic force 1122 ( / كلية التربية للعلوم الصرفة / جامعة كربلاء /4/ وقائع المؤتمر العلمي الرابع– الدولي الاول ) 21 631 microscope (AFM) diagnosis has led the doping process to increase in the roughness of the surface and the average rate of the square root with the variation in particle size distribution, In this study, it was prepared NO2 gas sensor had been prepared from ZrO2 pure film and doping with cobalt tinged with by 8% on the glass and silicon substrates. it was all change from Sensitivity membranes ZrO2, ZrO2:Co of NO2 gas with a temperature change, and measuring the change in resistance with the change of time at a temperature of certain operating account. The recorded a maximum value Sensitivity film ZrO2 pure precipitator on Silicon Substrate from 34.808% at the operating temperature 300ᵒC. and value Sensitivity film ZrO2 doped with titanium and precipitator on Substrate glass amounted to 34.517% at operating temperature 250ᵒC.

2017

Structure, surface topography and optical characterization of Ag co – doped Cd1-xCuxO nanostructure thin films

AuthorsAdel H. Omran Alkhayatt, -------
JournalJournal of Kufa - physics مجلة الكوفة للفيزياء
Abstract

Cd1-xCuxO and Ag co-doped Cd1-xCuxO nanostructure thin films with x = 0.2 and different Ag content (0-8%) were deposited by chemical spray pyrolysis technique on glass substrates at a temperature of 350 oC. The XRD results showed that the prepared films have polycrystalline with low crystallinity nature for CdO cubic structure. The preferential orientation of all films was absorbed along (111) plane. CuO monoclinic phase has appeared with low intensity while the Ag cubic phase appeared only in 8% of Ag content. Structural parameters such as average crystallite size, dislocation density and micro-strain were also investigated. SEM images revealed that the surface morphology of the films consists of spherical shaped grains uniformly distributed without detectable micro-cracks and improved by Ag Co-doping. EDXS spectrum analysis confirmed purity and stoichiometry of the prepared compositions. AFM results showed that the surface topography and the surface quality of the deposited thin films can be controlled by the variation of the Ag co-doping concentration. Optical absorbance and transmittance of Ag co-doped Cd1-xCuxO thin films has high values in the visible and near infrared regions respectively and varied with Ag co-doping content. Direct optical energy band gap of Cd1-xCuxO exhibits a blue shift with Ag co-doping, due to the quantum size and Burstein–Moss (BM) effects. The increasing of optical energy gap was confirmed by the decrease in the Urbach tails energy EU after Ag co-doping

2016

The Effect of Magnetic Field on Helium Plasma Characteristics of Discharge Tube

AuthorsMahdya A. Yeser, Adel H. Omran Nibras F. Ali Einas R. Wadaa
JournalJOURNAL OF KUFA – PHYSICS, Vol.8, No.1, (2016)
Abstract

The effect of discharge voltage of a discharge tube were investigated.The discharge voltage (700,800,900,1000,1100,1200) volt were applied under pressure of helium gas was (7Pa) and the inter electrode distance was (130mm). The measurements were achieved without and with parallel magnetic field of (25 mT). The electron temperature calculated from Id – Vd characteristics curves of double Langmuir probe. Results of electron temperature indicated that the behavior of electron temperature decreased with increasing the discharge voltage with and without the magnetic field.But their values at (B=0) was smaller than the corresponding values at (B=25 mT).

2016

Influences ofpost-annealingtemperatureonthestructuraland electrical propertiesofmixedoxides(CuFeO2 and CuFe2O4) thin films preparedbyspraypyrolysistechnique

AuthorsS.M.Thahab, AdelH.OmranAlkhayatt , InassAbdulahZgair
JournalMaterialsScienceinSemiconductorProcessing
Abstract

P-typemixedoxides(CuFeO2 and CuFe2O4) transparentconductingthin films havebeensuccessfully deposited onp-typeSi(111)substratesat450 °C byspraypyrolysisdeposition(SPD)andannealedat 800 °C for2h.Thecrystalstructure,surfacemorphologyandelectricalpropertyhavebeeninvestigated. It isobservedthattheCuFeO2 and CuFe2O4 thin films asdepositedandannealed,havepolycrystalline hexagonalstructureandthecrystallitesizeincreasesbyannealingprocesses.Theelectricalpropertyof the Ni/CuFeO2/Si Metal–Semiconductor–Metal (MSM)photodetectorswasinvestigatedusingthecur- rent–voltage(I–V) measurements.Thebarrierheights ϕΒ of Ni/CuFeO2/Ni MSMthin films ofasdeposited and annealedonSisubstrateswerecalculatedanditsvaluesare0.478,0.345eV,respectivelywithan applied biasvoltageof3V.

2016

Rheological and optical characterization of Polyvinylpyrrolidone (PVP) - Polyethylene glycol (PEG) polymer blends

AuthorsAdel H.Omran Alkhayatt1, Ali H. Al-Azzawi2, Zahraa Alakayashi1, Ali H. Al-Azzawi, ZahraaAlakayashi
JournalIOSR Journal of Applied Physics (IOSR-JAP) 1.Volume 8, Issue 1 Ver. I (Jan. - Feb. 2016), PP 11-18
Abstract

Abstract : Polymer blends of different concentrations for PVP-K30 and different additive weights of PEG8000 have been prepared as polymeric blends solutions. The rheological and optical properties of the blends samples have been investigated using Ostwald viscometer and Refractometer. The results show that the density, shear, relative and specific viscosities are increases with the increasing of PVP concentration and additive weight of PEG. The optical constant values such as refractive index, reflectance, molar reflectance, coefficient of finesse and Brewster Angle are increase with the increasing of PVP concentration and additive weight of PEG while the critical angle has the revers behavior.

2016

Structure, surface morphology and optical properties ofpost-annealed delafossite CuFeO2thin films

AuthorsAdel H.Omran Alkhayatt, Sabah M. Thahabb, Inass Abdulah Zgairaa
JournalOptik 127 (2016) 3745–3749 www.elsevier.de/ijleo
Abstract

tDelafossite CuFeO2(TCO) thin films have been successfully deposited onto quartz substrate by low-costchemical spray pyrolysis at 450◦C and post-annealed at 800◦C for 2 h. The XRD results for as deposited andpost-annealed films show polycrystalline structure with Hexagonal (Rhombohedral) phase. The CuFe2O4phase appeared as the film deposited and post-annealed. The preferred orientation was along (0 1 2)plane and the crystallite size increased from 20.89 nm to 22.588 nm after annealing process. The surfacemorphology of CuFeO2thin film seems relatively smooth and plated regularly; the EDX spectra confirmthe stoichiometry of the prepared films. The average roughness values obtained from AFM measurementshave been decreases from and from (19.7 to 14.4 nm) respectively after annealing process. The opticaltransmission of these films has been studied in the wavelength range 400–800 nm and found to be morethan 62%. The direct optical band gap of the CuFeO2films was 2.66 eV and decreased to 2.63 eV afterannealing process. The Urbach’s energy was found to be increase from 0.247 eV for as deposited film at450◦C to 0.2857 eV after annealing process.

2016

SYNTHESIS AND STRUCTURAL CHARACTERIZATION OF SOL-GEL DEPOSITED FLUORINE DOPED NANOCRYTALLINE CdS THIN FILMS

AuthorsADEL H. OMRAN ALKHAYATT, ADEL H. OMRAN ALKHAYATT, GHOFRAN MOHAMMED HUSSEIN AL-HADDAD
JournalIMPACT: International Journal of Research in Applied, Natural and Social Sciences Vol. 4, Issue 5
Abstract

In this study, pure and Fluorine (5,10 and 15 wt%) doped CdS thin films were prepared on glass substrate by solgel spin coating method dried at temperature 250 °C for 15 min. and annealed at temperature 450 °C for 2h. Structural properties, surface morphology of CdS and CdS: F thin films have been investigated with respect to the doping process. The X-ray diffraction (XRD) results point to that the structure of all prepared thin films are polycrystalline in nature and has a Hexagonal (Wurtzite) phase, CdS and CdO cubic phases was found related to annealing temperature and air ambient. The average grain size of CdS film was53.4 nm and increases as fluorine dopant concentration increase with maximum value of 97.3 nm for CdS:F (15wt%) so the pure and doped films have nanocrystalline structure. The introducing of fluorine does not affect the structural properties of the films. The Scanning Electron Microscopy (SEM) image for CdS and CdS:F thin films shows that smooth, uniform morphology and plated regularly. The stoichiometry of CdS:F prepared films confirmed by the energy dispersion x-ray spectroscopy (EDX) specta. Consequences of atomic force microscope (AFM) images for CdS and Cds:F thin films displayed smooth surface texture.

2015

Fluorine highly doped nanocrystalline SnO2 thin films prepared by SPD technique

AuthorsAdel H. Omran Alkhayatt, Shymaa K. Hussian
JournalElsevier - Science Direct
Abstract

Pure and fluorine highly doped SnO2 (TO and FTO) thin films with different dopant concentrations (0.15, 0.25, 0.35 mol/l) have been prepared by spray pyrolysis technique at substrate temperature 450 1C. The crystal structure and surface morphology of the prepared films were characterized by using X-ray diffraction and scanning electron microscopy SEM. The XRD patterns show polycrystalline structure in nature with tetragonal (rutile) phase. The average crystallite size decreases with increasing of dopant concentrations and its values in the range (32–56) nm which indicate that all films have nanocrystalline structure. The SEM images show a homogeneous and smooth uniform surface with no detectable microcracks, the EDX spectra confirm the stoichiometry of the prepared films. The optical properties of the films were investigated by UV–vis spectrophotometer. In the visible range, the optical transmittance (T%) of the films with varying dopant concentrations was found to be (83–98)% and the fundamental absorption edge shifted toward higher energies (blue shift) with increasing of fluorine dopant concentration. The energy band gap value of pure SnO2 was 3.95 eV and it increases to 4.04, 4.08 and 4.1 eV with the increasing of dopant concentration, this behaviors can be attribute to the (B.M) effect or Burstein–Moss shift.

2014

Characteristics of Nanocrystalline ZnS thin films grown on glass with different Zn ion concentrations by CBD technique.

AuthorsAdel H. Omran Alkhayatt1, Mustafa D. Jaafer
JournalIOSR Journal of Applied Physics (IOSR-JAP)
Abstract

Thin films of zinc sulfide (ZnS) with various values of Zn ions concentrations (0.2,0.3,0.4)M have been prepared by Chemical Bath Deposition Technique on glass slides substrate at 80 ºC bath temperature. The prepared films were annealed in air at constant temperature 400 ºC and constant time (180) min . Structural and optical properties of ZnS thin films were investigated and analyzed extensively before and after annealing . The structure properties of the prepared films were studied by using x-ray diffraction technique , it has been found that all prepared films at different Zn ions concentrations were amorphous structure, while the annealed films showed polycrystalline structure type (Hexagonal) , The lattice constants (a , c) of ZnS films were calculated and its values found about (3.86,31.6) Å , the crystallite size (Grain size) of ZnS thin films also calculated and found to vary from (20.8 to 83.7) nm ,which indicate that annealed ZnS thin films has Nanocrystalline structure . The optical properties of ZnS thin films contained study of transmittance spectrum in the range of wave length (190-1100)nm by using UV- ViS. Spectrophotometer was carried out. Transmittance decreased with increasing the Zn ions concentrations of ZnS films , also the transmittance decreased after annealing . The fundamental absorption edge of ZnS thin films shifted toward the highest photon energies (blue shift) with increasing the Zn ions concentration and shifted toward the lowest photon energies (red shift) after annealing. The absorption coefficient values which calculated from the absorbance spectrum was larger than 104cm-1 gives an indicate that ZnS films were direct semiconductors and the electronic transitions was a direct transitions. The optical energy gap values for allowed direct transition found in the range of , (1.594-3.060) eV for (ZnS) thin films with (0.2 - 0.4 M) Zn ions concentration and in the range of (3.215-3.099) eV for the same concentrations after annealing.

2014

Annealing Effect on the Structural and Optical Properties of Sol- Gel Deposited Nanocrystalline CdO Thin Films

AuthorsAdel H.Omran Alkhayatt, Imad A. Disher Al-hussainy, Oday A. Chichan Al-rikaby
JournalAdvances in Physics Theories and Applications
Abstract

In this paper CdO thin films have been prepared by using SOL-GEL method with spin coating technique, by depoited four layers of mixtuer solution contians Cadmium acetate dehydrate, Triethylamine, glycerol and ethanol.The spin coated solution were dried at 100°C and annealied at (300,350 and 400 oC temperatures ). The x-ray diffraction techniques and UV-VIS spectrophotometer have confirmed the structural and the optical properties the prepared thin films. CdO thin films were found to have polycrystalline nature with cubic rock salt phase. The crystallinity being improved, the FWHM decreases and the grain size of the CdO thin films increased with increasing the annealing temperatures. The average grain size is observed in the range (23.97 - 30.47) nm which indicate that the prepared film have a nanocrystalline structure. From optical analysis, it can be seen that there are an increases in the absorbance and decreases in the trancemittance of the prepared films with the increasing of the annealing temperatures.The optical band gap decreases from 2.556, to 2.081 eV with increasing of annealing temperature fromm 300 to 400° C, this suggested that the optical band gap for CdO nanocrystalline thin films is strongly dependent on the annealing temperature

2014

Study the Structural and Morphological Properties of CdxZn1-xS Thin Films prepared by Chemical Spray Pyrolysis Technique (CSP)

AuthorsAdel H. Omran Alkhayat, S.M.Thahab and Salah M. Saleh
Journalمجلة الكوفة للفيزياء / قسم الفيزياء / كلية العلوم
Abstract

CdxZn1-xS thin films have been prepared by the chemical spray pyrolysis method on glass substrate. The structural, compositional properties of CdxZn1-xS thin films have been investigated using X-ray diffraction. As-deposited CdxZn1-xS thin films are polycrystalline and show the hexagonal (Wurtzite) with the highly preferential orientation (002). The surface morphology and defects of CdxZn1-xS thin films have been investigated using (SEM) and (EDAX). The morphology of thesis thin films indicate that the size of the particles increased with Cd2+ concentration. However, EDAX spectra indicated well defined peaks corresponding to Zn, Cd and S. the surface texture of the deposited CdxZn1-xS thin film have been investigated using AFM. The AFM show deposited of Cd0.5Zn0.5S thin film on glass substrates exhibits the smooth surface texture.

2014

The optical Properties of Fe2O3 Thin Film Prepared By Chemical spray pyrolysis Deposition (CSP)

AuthorsSaadi. A. J. AL- Dahaan, Adel. H. Omran Al-khayatt , Mustafa.K. Salman
Journalمجلة الكوفة للفيزياء / قسم الفيزياء / كلية العلوم / جامعة الكوفة
Abstract

In this work, Fe2O3thin films have been prepared on glass substrate by chemical spray pyrolysis (CSP) technique at temperature 450oC. Structural and optical properties of Fe2O3 thin films have been investigated and analyzed extensively with respect to deposition time. The XRD results indicate that the structure of all prepared thin films from aqueous solutions FeCl3 were polycrystalline in nature and has a rhombohedral (hexagonal) phase with preferred orientation along (104) plane. The average grain size values for all prepared films have been found in the range from 76.543 to 83.258 nm , which indicates that all films have been Nano crystalline .The absorbance and transmittance spectra have been recorded in the wavelength range 300- 600 nm, which showed that the absorption edges of Fe2O3 thin films differed at different deposition times. The optical band gap for allowed direct transition has been decreased from (2.4813 to 2.449 )eV and with increasing deposition time. Moreover, the effect of deposition time on optical constants (absorption coefficient, reflectance, extinction coefficient, and refractive) has been investigated.

2014

Influenceofsubstratetypeonthestructural,opticaland electrical propertiesofCdxZn1xS MSMthinfilmspreparedby SprayPyrolysismethod

AuthorsS.M. Thahab , AdelH.OmranAlkhayat b, SalahM.Saleh
JournalElsevier, ScienceDirect
Abstract

0.25 μm CdxZn1xS thinfilmsweredepositedonSiandglasssubstratesbyusinga chemicalSprayPyrolysistechnique(CSP).Measurementsoftheabsorptionspectrumof the filmwerecarriedout.Thevaluesofbandgaps(Eg) arecalculatedfromtheabsorption spectrum.X-raydiffraction(XRD)oftheCdxZn1xS thinfilmsonSiandglasssubstrates wascarriedout.Thefullwidthathalf-maximum(FWHM))ofdiffractionpeakwas calculatedtobeabout0.640,whichshowedthatitisapolycrystallinethinfilm. A CdxZn1xS Metal–Semiconductor–Metal (MSM)photodetectorwithnickel(Ni)contact electrodes wasthenfabricated.TheelectricalpropertyoftheNi/CdxZn1xS/Si andNi/ CdxZn1xS/glass detectorswasinvestigatedusingthecurrent–voltage (I–V) measure- ments. Thebarrierheights ϕΒ of Ni/CdxZn1xS/Ni MSMonSiandglasssubstrateswere 0.551eVand0.593eV,respectivelywithanappliedbiasvoltageof3V.

2014

The optical properties of CdxZn1−xS thin films on glass substrateprepared by spray pyrolysis method

AuthorsS.M. Thahaba ., Adel H. Omran Alkhayatb, Salah M. Saleh
JournalScienceDirect .Elsevier
Abstract

tA series of CdxZn1−xS thin films have been deposited on glass substrates using spray pyrolysis technique.The crystallinity and microstructure of CdxZn1−xS thin films have been investigated by X-ray diffraction(XRD). Based on the results of Hall measurements, the films obtained were an n-type semiconductor. TheX-ray data analysis of CdxZn1−xS thin films showed that the grain size of the CdxZn1−xS increased withincrease in Cd composition. It is observed that the band gap increases as the Cd composition decreases.The results also showed a blue shift of absorption edge of optical transmission spectra is increases as Znratio increases. The effects of Cd composition on the structural and optical properties of CdxZn1−xS thinfilms were related to their grain size, stress and carrier concentration.

2014

Nanocrystalline CuFeO2 Delafossite Thin Films Prepared on Quartz by CSP Method

AuthorsAdel H.Omran Alkhayatt, S. M.Thahab , Inass Abdulah Zgair
JournalApplied Numerical Mathematics and Scientific Computation
Abstract

Abstract-Transparent conductive CuFeO2 thin films have been deposited on quartz substrate at 450°C using chemical spray pyrolysis technique and then annealed at 800°C for 2 h. The structural properties of CuFeO2 thin films have been studied by XRD. The diffraction pattern show that CuFeO2 films are polycrystalline in nature with hexagonal (Rhombohedral) structure. The preferred orientation along (012) plane, the grain size increases from 29.61nm to 39.566nm after annealing process. The optical properties have been investigated by UVVIS spectrophotometer in the wavelength rang 300- 800 nm, the result shows that the prepared film had transmittance at visible region about 62% and the absorption edge shifted towards long wavelength after annealing process. The direct band gap value of as deposited CuFeO2 thin film was 2.66 eV and its decreases to 2.63eV for annealed film.

2013

Structural and Optical characterization of Nanocrystalline SnO2 thin film prepared by spray pyrolysis technique

AuthorsAdel H.Omran, Shymaa K. Hussian
Journalمجلة الكوفة للفيزياء
Abstract

Nanocrystalline Tin Oxide SnO2 thin films have been grown on cleaned glass substrates at 450 C○ using spray pyrolysis deposition technique, prepared from two precursor solutions SnCl2.2H2O and SnCl4.5H2O.The XRD analyses showed that these films have polycrystalline in nature with tetragonal rutile structure with preferred orientation of (110),(200),(211) and the crystalline size (grain size) of thin films are found to vary from 32.6 to 56.98 nm . UV -VIS spectra of the films were studied using the optical absorbance measurements which were taken in the spectral region from 190 nm to 1100 nm. The transmittance and ref1ectance spectra of the films in the UV -VIS region were also studied. Optical Constants such as optical band gap, absorption coefficient and extinction coefficient, were evaluated from these spectra. All the films were found to exhibit high transmittance greater than (~ 85 %), and high absorbance values at ultraviolet region which they decrease rapidly in the visible / near infrared region. The optical band gap energy was found 3.98 eV for sample A and 3.97 eV for sample B.

2013

Annealing Effect on The Structural and Optical Properties of CuS Thin Film Prepared By Chemical Bath Deposition (CBD)

AuthorsAdel H. Omran Al-khayatt, Mustafa D. Jaafer
Journalمجلة الكوفة للفيزياء
Abstract

Thin films of copper sulfide (CuS) with various molarities values of Cu concentrations (0.2,0.3,0.4)M have been prepared by Chemical Bath Deposition Technique on glass slides substrate at room temperature . The prepared films with different ion concentrations were annealed in air at constant temperature 400 ºC and constant time (180) min .Structural and optical properties of CuS thin films were investigated and analyzed extensively before and after annealing . The structure of the prepared films has been found with amorphous structure at different Cu ion concentrations , annealed CuS films also showed amorphous structure. The optical properties of CuS thin films has been studied by transmittance and absorbance spectral in the range of wave length (190-1100)nm by using UV- Vis. spectrophotometer. Transmittance decreased with increasing the Cu ion concentrations of CuS films, also the transmittance increased with annealing process for (CuS) thin films. The fundamental absorption edge of (CuS) thin films shifted to word the lowest photon energies with increasing the Cu ions concentrations before and after annealing. From the absorption coefficient values which calculated from the absorbance spectrum which is larger than 10-4cm-1 gives an indicate that CuS films were direct semiconductors and the electronic transition was a direct transition. The optical energy gap values of CuS thin films for allowed direct transition found vary in the range between (2.433-2.526) eV with (0.2- 0.4 M) Cu ions concentration and in the range of (2.416-2.349) eV for the same concentrations after annealing. The optical constant such as reflectance ( R ), absorption coefficient (α), refractive index (n) and extinction coefficient (K) were evaluated and analyzed .

2011

The development and studies the current – voltage (I-V) characteristics for the metal- oxide-semiconductor field- effect transistor MOSFET

AuthorsAdel H.Omran Alkhayatt, ,E.M.Abass Y.N.Obaid , A.S.Al-Rowass
Journalمجلة الكوفة للفيزياء Journal of Kufa Physics
Abstract

This paper contain the preparation of metal-oxide- semiconductor field- effect transistor MOSFET by using the lightography technique. In this work we studied (IV) characteristics and also some physical variables for transistor calculated. The prepared transistor by using p- type silicon as a substrate has n-type channel (nMOSFET) its length and width equal to L=50 μm ,Z = 1000μm . The results showed that the output characteristics (ID-VD) and the trasfer charasteristics (IDVG) was in agreement with the theoretical behaviour of the transistor , and the transistor is from the normally – on type nMOSFET depletion mode , with pinch – off voltage equal to -4 volt .

2010

Irradiation effect on the structural properties and optical energy gap of Thin films CdOxCuO1

AuthorsAdel H. Omran Alkhayatt, Yassin N. Obaid
JournalJOURNAL OF KUFA PHYSICS مجلة الكوفة للفيزياء
Abstract

This study deals with preparation of CdOxCuO1-x thin films by chemical spray pyrolysis technique, and the irradiation effect of (γ-ray) with a radiation dose of (220 K Gray) which equal to (22 M rad) on the structural properties and the optical energy gap of the prepared films on thin glass substrates heated to 633 ˚K and of 280±20 nm thickness. The (x-ray) testing results showed that all films had polycrystalline structure , and the irradiation films with (γ-ray) reduced the diffraction peaks as well as the intensities of CdO and CuO films and making the mixed films of random structures. The optical energy gap results showed that all films had direct (allowed and forbidden) energy gap. The irradiation reduced the value of the forbidden energy gap. The study also showed that the forbidden energy gap reduces with the increases of CuO rate in the film.

2010

بناء منظومة رش كيميائي حراري لتحضير المواد الصلبه على شكل اغشيه رقيقه ودراسة الخواص الفيزياويه للمواد المحضره

Authorsعادل حبيب عمران, صالح حسون عبود
Journalمجلة الكوفة للفيزياء
Abstract

يتضمن المشروع بناء منظومة لتحضير الأغشية رقيقة thin films لمختلف المواد الصللبة وبطريقلة اللرش الكيميلائي الحلراري (Chemical spray pyrolysis) . هل ه الأغشليه اات اسلتقرارية وابلات علاليين فلي الخصلائ الفيزيائيله للملواد المحضره منها, ل لك تكون معتمدة النتائج لأغراض البحوث والدراسات. حيث تم تحضير اغشلية اوكسليد النيكلل NiO وأغشلية كبريتيد الكادميوم CdS الرقيقه به ه الطريقه . وتمل دراسلة الخصلائ البصلريه لغغشليه المحضلره فلي المنطقله المرئيله – فوق البنفسجيه UV- VIS من الطيف الكهرومغناطيسي من خلال تسجيل طيف الأمتصاصيه والنفاايه لغغشيه المحضره فلي مدى الأطوال الموجيله (300-1100) nm . أطيلا الأععكاسليه لغغشليه المحضلره درسل أيضلا فلي عفله المنطقله . ال وابل البصريه لغغشليه المحضلره م لل معاملل الأمتصلاص ومعاملل الخملود ومعاملل الأعكسلار حسلب ملن تللك الأطيلا . الأغشليه المحضره وجدت أعها اات فجوة طاقه مباشره وقيمة طاقة الفجوه الممنوعه لأغشية NiO هي 3.694 eV بينما قيمتها لأغشلية CdS هي 2.471 eV .

2009

Studying the capacitance – voltage (C-V) characteristics for the metal- oxide-semiconductor field- effect transistor MOSFET fabricated by photolithography technique

AuthorsAdel H.Omran AlKahyatt, , Dr. E.M.Abass Dr.Y.N.Obaid, Dr.A.S.Al-Rowass
JournalJournal of Kufa Physics مجلة الكوفة للفيزياء
Abstract

This paper contain the fabrication of metal-oxide- semiconductor field- effect transistor MOSFET by using the lithography technique and studying of (C-V) characteristics in the reveres and forward bias and the effect of frequency variation on it, with calculate some important physical variable parameters for it. The fabricated transistor by using p- type silicon as a substrate has n-type channel (n- MOSFET) its length and width equal to L=50 μm ,Z = 1000μm . The results showed thatthe capacity (CG) was decreases with the increasing of the gate voltage VG in the reverse bias with frequencies (100,200,400,500) KHz, and the capacity decreases with the increasing of the applied current frequency. The results also showed that the capacity CG increases with the increasing of the gate voltage VG in the forward bias with the same frequencies and the capacity decreases with the increasing of the applied current frequency. The behavior of capacity-voltage in the forward and reveres biases is in good agreement with the theoretical behavior of the transistor

2008

The Effect of Different Wavelengths on Porous Silicon Formation Process

AuthorsOday A. Abbas, ,Abbas H. Rahim, Adel H. Omran
Journalمجلة كلية التربية / جامعة بابل
Abstract

ABSTRACT Porous silicon layers (PS) have been prepared in this work via Photo-electrochemical etching process (PEC) of n-type silicon wafer of 0.8 Ω.cm resistivity in hydrofluoric (HF) acid of 24.5 % concentration at different etching times (5 – 25min.). The irradiation has been achieved using Tungsten lamp with different wavelengths (450 nm, 535 nm and 700 nm). The morphological properties of these layers such as surface morphology, Porosity, layer thickness, and also the etching rate have been investigated using optical microscopy and the gravimetric method.

2008

Studying Vibrational Frequencies of the Schiff's Base Liquid Crystal Molecule by Using Mindo/3-Forces Program

AuthorsAbbas H. Raheem , Adel H. Omran ,Oday A. Abbas
Journalمجلة علوم المستنصرية
Abstract

In advance to syntheses in the laboratory , it very useful, to have quick and easy procedures available, allowing the calculation of spectroscopic and molecular data of liquid crystal materials without any experimental basis by using different quantum chemical methods .We are studying modes of fundamental vibrations and calculation of vibrational frequencies in addition to identification both fundamental and unfundamental branches of the Schiff's base liquid crystal molecule (OBOMe) [4- ( 4'- n-Octyloxybenzoyloxy) -2- hydroxybenzylidene - 4" –methoxylaniline] by using Mindo/3-forces program, specially for functional group to this molecule such as (C-O,C=O,C-H,O-H,C=N,.…..) in order to using in important industrial and medical applications. We also calculate molecular data like bond length and force constants. These results for liquid crystal molecule have been obtained by Mindo/3-forces program which study vibrational energy level for molecule in single state without any hydrogen bonding.

2008

Optical characteristics of CdS thin film on glass formed by Chemical spray pyrolysis

AuthorsDr.Adel .H.Omran.Alkhayatt
Journalمجلة القادسية
Abstract

Cadmium sulfide (CdS) thin films have been grown on cleaned glass substrates at 623 oK temperature using spray pyrolysis deposition technique in different thicknesses. UV.-VIS. spectra of the films were studied using the optical absorbance measurements which were taken in the spectral region from 300 nm to 1100 nm. The transmittance and reflectance spectra of the films in the UV.-VIS. region were also studied. Optical Constants such as optical band gap, absorption coefficient and extinction coefficient, were evaluated from these spectra. All the films were found to exhibit high transmittance (~ 50 - 84 %), low absorbance and low reflectance in the visible/ near infrared region from ~ 500 nm to1100 nm. The optical band gap energy was found to be in the range 2.421 – 2.523 eV.

Lectures

12

News & Announcements

2
News 2016-11-15

My Google Scholar Site https://scholar.google.com/citations?hl=en&user=YWDqIWoAAAAJ

Assist. Prof. of Solid State Physics Science ,Faculty of Science / Kufa University Solid state electronics, Thin Films, Nanoparticles and Nanomaterials, materials science, Nanoparticles Verified email at uokufa.edu.iq - Homepage My profile is public

News 2016-11-15

My Scopus Site https://www.scopus.com/authid/detail.uri?authorId=56131767100&eid=2-s2.0-84903683365

My Scopus web page Elsevier and Spriger

View details